Guardian 2D/3D Stabilizer
Master your Skies!
Based on Eagle Tree's proven inertial stabilization technology, the Guardian 2D/3D Stabilizer is a must-have product for your model. The Guardian smoothes out air turbulence, but does much more. Unlike cheap “gyro stabilizers," it provides true wing leveling capability to help recover from lost orientation!
Whether you fly gas or electric models, wings, foamies, sailplanes, or just about any other fixed wing model, the Guardian is for you! Is it moderately gusty or windy? The Guardian helps compensate for non-ideal flying conditions. The Guardian helps your plane fly like it's a perfectly calm day!
To stabilize your model, just mount the Guardian in a level orientation (it can even be mounted upside down), connect it to your servos and receiver with the included cable, tune it to your plane with a small screwdriver, and set optional features with your radio sticks. No computer or additional equipment is required for stabilization.
While in flight, a spare switch on your radio lets you switch between 2D (wing leveling) mode, 3D aerobatic mode, and no stabilization. Imagine performing a difficult 3D maneuver with ease, then just flipping a switch to instantly return to level flight!
At only $74.99 (USD, MSRP) the Guardian provides some great protection for your investment, while making it more fun to fly and easier to perform advanced maneuvers!
Q: Why do I need the Guardian?
The Guardian helps both beginner and expert pilots fly with confidence, and provides two key modes of operation:
In 2D flight mode, the Guardian provides much smoother flight and wing leveling stabilization for your model, which makes it a lot easier to adjust and fly your plane. The Guardian "remembers" level flight for your model and returns it to level flight when needed, as well as providing precise "fly by wire" control. You may think that your model is on rails! The Guardian is also great for FPV flying.
If you are a beginner pilot, the Guardian can help take the fear factor out of the first few flights. If you get into trouble, just let the sticks go and the Guardian will attempt to quickly bring your model back to level flight.
If you are flying a plane that is not very stable due to imbalance, poor aerodynamics or high motor torque, the Guardian can make things much easier.
Is it moderately gusty or windy? The Guardian helps compensate for non-ideal flying conditions. The Guardian helps your plane fly like it's a perfectly calm day!
In 3D flight mode, the Guardian becomes your aerobatic assistant. Whether you want to become a 3D expert, or already are, the Guardian can turn your squirrelly stunt plane into a kitten, without sacrificing aerobatic capability.
The Guardian updates your control surfaces much faster than most humans can, to provide real time corrections to the flight. So, you can concentrate on your maneuver, rather than fighting the model to maintain control. The Guardian makes your plane "snappier" for precision maneuvers.
The Guardian has two submodes for 3D flying:
In 3D Heading Lock submode, simply center your sticks to have the Guardian lock onto your present attitude (pitch, roll, and heading), which can make it easier to perform stunts like prop hanging, inverted flight, knife edges, low speed harriers, etc!
In 3D Gyro submode, the Guardian uses its built-in 3 axis gyro to increase your model’s stability, while leaving you in full control. In this mode the Guardian greatly reduces the effects of gusts, turbulence, motor torque and other factors, and can expand the maneuverability of your model in a variety of conditions.
Q: I Fly FPV. Is the Guardian for me?
Yes! We offer two great stabilization solutions for FPV flyers. If you plan on using an OSD with FPV, we recommend the Vector OSD, with built-in Guardian stabilization. This gives you integrated FPV stabilization with AHI (artificial horizon) display, easily adjusted with on-screen video menus.
If you don't need an OSD with your FPV plane, or are using an OSD other than the OSD Pro, the Guardian 2D/3D Stabilizer should be perfect for you.
Also, we plan to have firmware updates for the Guardian 2D/3D Stabilizer for camera stabilization!
Q: Will the Guardian work with my model?
The Guardian weighs only about 11 grams with cable, and has a tiny footprint, so it is perfect for most models, from small foamies on up. But don't let its small size fool you - it works great in almost any fixed-wing plane! And, there are no external sensors to add drag or weight to your model.
The Guardian controls a total of 4 servos, and is flexible enough to support elevons, dual ailerons, and other configurations.
Servo compatibility notice: Eagle Tree has received reports that some instances of the E-Flite™ model EFLR7155 servo do not work correctly with the Guardian (and some similar devices) due to higher than normal loads placed on the servo signal line, while other instances of this servo model do not exhibit this behavior. Symptoms can include sudden, uncommanded servo movements. Therefore, we cannot recommend using this model servo with the Guardian.
Q: How do I install the Guardian?
Guardian installation is quite easy. Simply mount the Guardian securely in your model's fuselage, and connect it to your receiver and servos. The labeled receiver connectors on the included cable make this step very simple. There are no additional sensors or other hardware to install!
At a minimum, your ailerons (or rudder) and elevator need to be left connected, but the Guardian includes additional control and stabilization channels to support almost any model! Stabilization gain can be controlled via an extra knob on your radio, which lets you easily adjust it in flight.
Q: How do I configure the Guardian?
After installation, the Guardian is tuned to your plane using only a small screwdriver, and settings are chosen via your radio sticks. No computer or other device is required for configuration!
Gain can also be adjusted in the air with a spare knob or switch on your receiver, if desired.
If you prefer PC setup, just connect the Guardian to your Windows PC or laptop via the built-in USB connector*, and run our software to perform advanced configuration with ease!
Our PC software also allows you to save and restore model profiles, making it easy to move the Guardian from plane to plane without reconfiguration!
Q: How does the Guardian work?
The Guardian's built-in state of the art sensors constantly measure the gravitational forces and rotation of your model in 3 axes (6DOF IMU). Using the sensor data, the Guardian's processor performs complex calculations thousands of times a minute to keep track of your model's orientation.
Q: What sets the Guardian apart from other Stabilization systems out there?
Previously, the only stabilization systems available required installing external sensors, or were relatively large, heavy and expensive. The Guardian changes all that. At only $74.99 (USD MSRP), the Guardian is priced much lower than any other inertial based stabilization systems, and is much lighter and smaller than anything else out there, at any price.
The Guardian smoothes out air turbulence, but does much more. Unlike cheap “gyro stabilizers," it provides true wing leveling capability to help recover from lost orientation!
And of course, it's an Eagle Tree product, so it's massively configurable and has built in USB* for advanced configuration, model profile save/restore, and firmware update from the internet. No need to return the unit to the shop or buy a USB convertor board for new firmware updates!
The Guardian has a built-in data port, and we have plans for future sensors and hardware features. Please let us know what else you want the Guardian to do!
Q: I want one for each of my models! When and where can I buy it??
Contact your favorite RC dealer, or order direct from us if a dealer is not in your area.
Q: Where can I find more details?
Click here for the Guardian 2D/3D Stabilizer thread on RCGroups.com.
Q: You are missing the feature I want! How do I tell you what you need to add?
Eagle Tree is very interested in how we can improve our products to meet your needs. Just post your request on the Guardian Stabilizer thread here, or email us and let us know what you need!
* Note: a standard "micro" USB cable, used commonly with mobile phones and eBooks, is not included but is required for PC configuration and firmware update. You probably already have one, but if not, you can purchase it from us or elsewhere.
· Input Voltage Range: 4.5v to 16v
· Current Draw: Approximately 31mA
· Dimensions: 41mm x 22mm x 11mm (1.62 inches x 0.86 inches x 0.42 inches)
· Mass: 11 grams (0.4 ounces) including harness
· Maximum Servo Current through Guardian: 5 Amps
Package includes Guardian 2d/3d Stabilizer and receiver connection harness
Note: You can use this product by itself-- no other Eagle Tree or FPV gear is required!
Here is a video tutorial of Guardian installation and configuration: